ICA Corporation

12130 Brockton Lane
Maple Grove, MN 55369
Ph: 800-345-2801
Fax: 763-428-4230


Photo Gallery


Optical Frame Assembly - Numerous aluminum machined parts, extruded rails, anti-vibration leveling mounts, and sheet metal fabricated parts make up this frame assembly used for an analytical instrument. Frame is then completed with painted and silkscreened panels.

Chassis - Laser cut from 18 gauge CRS, measures 19" x 11" x 9". After forming, hardware is installed and part is zinc plated. Used in the Printing Equipment industry.

Atomizer - Manufactured for a laboratory instrument, this 9 piece assembly as 8 parts machined from 316L stainless steel and 1 part machined from Delrin. After welding, the assembly is mechanically polished and electro polished. Fine surface finishes are required to minimize lodging of particles. A .013" cross hole is drilled and must be completely burr-free.


Heater Block - Tolerances are critical to this part used in an analytical instrument. Measures 1.16" x .75" and made from 6061-T6 aluminum with electroless nickel finish.

Upper Cam - Made from 6061-T6 aluminum with hard coat anodize. Extremely tight tolerance part for a laboratory instrument measuring 2" x 1.5".

Enclosure - Riveted assembly made from 13 gauge and 16 gauge CRS, measuring 21" x 5" x 10". Finished with yellow zinc plating. Used in the Telecommunications industry.


Imager Housing - Machined from 6061-T6 aluminum with an anodize finish and measures 4" x 2.5" x 2.5". Extremely tight tolerancing of several features. Housing for an infrared camera.

Cover - Machined from 6061-T6 aluminum and zinc plated. This part measures 15.25" x 6.75" x 1" and is assembled with hardware and heat sinks. Part of a ruggedized computer.

PCB Bracket - Two piece construction made from 20 gauge CRS, with embosses and spotweld stiffener. Finish is bright electro tin plate. Part measures 2.25" x .75" x 1.125" and is part of a sensor.


Aluminum Chassis - Made from .090 5052-H32 aluminum, this chassis measures 27" x 15" x 17" and is finished with gold iridite and silkscreened. Special features include hardware, wire rope and rivets. Used in the Aerospace industry.


Card Rack - This rack measures 12" x 18" x 19.75" and is part of a laboratory instrument. Made from 16 gauge and 18 gauge CRS with clear zinc finish.



Front Cover - Machined from 6061-T6 aluminum and measures 12" x 9" x 2.5". Assembled with helicoils and standoffs. Used in the Aerospace industry.



Drive Assembly
  • Machined aluminum components
  • Precision linear bearings
  • Sensors
  • Electric motor
  • Bearing alignment is critical to maintain smooth drive

Display Assembly
  • 3/4" aluminum plate
  • Screwed assembly of 16 parts with specific torque requirements
  • Plated and painted
  • 24" wide x 46" high x 16" deep

Sheet Metal Chassis
  • Laser cut .125” aluminum
  • Spring loaded latch assembly
  • Polyurethane foam
  • Hinge
  • Hard anodize finish with silkscreen

Controller Frame Assembly
  • Laser cut 12 and 16 gage CRS
  • 31” x 24” x 32” high
  • Critical tolerances and dimensions are closely held at each operation to avoid costly fixtures

Vertical Drive Assembly
  • Machined parts from 6061-T6 aluminum and 303 stainless steel
  • Polymer bushings
  • Measures 8" high x 4.5" x 4.5"

Controller Cabinet - 31" x 20" x 29" cabinet made of 18 gauge CRS. Electro Dag primer with liquid nickel masked areas and textured paint. Used in the Printing industry.

© 2017 ICA Corporation All rights reserved. Web site designed and maintained by Design-2-Part Web Design.